rbrown7713 Posted November 3, 2022 Share Posted November 3, 2022 I am finally getting around to building an E7 A and B for the Broadway limited with some Finescale cars. This will complete my 4 trains with the correct locos with the correct, I hope, cars. I will have to replace the number boards on the cab to the earlier style. Bob. Quote Link to comment Share on other sites More sharing options...
Jerry B44 Posted November 3, 2022 Share Posted November 3, 2022 Busy guy, should be good. Quote Link to comment Share on other sites More sharing options...
Sean Posted November 7, 2022 Share Posted November 7, 2022 Bob nice to see you back at it ... Quote Link to comment Share on other sites More sharing options...
rbrown7713 Posted November 7, 2022 Author Share Posted November 7, 2022 Yes, my no. 1 interest is building I have both sides molded and I am going to pour some sides today. Bob Quote Link to comment Share on other sites More sharing options...
rbrown7713 Posted November 7, 2022 Author Share Posted November 7, 2022 Sorry I forgot, what are you up to these days. Bob. Quote Link to comment Share on other sites More sharing options...
rbrown7713 Posted November 17, 2022 Author Share Posted November 17, 2022 I am tooling up for the last big part, the roof, I, ve got all of the other parts, so almost ready to put it together. Bob. Quote Link to comment Share on other sites More sharing options...
Sean Posted November 17, 2022 Share Posted November 17, 2022 Quote Link to comment Share on other sites More sharing options...
rbrown7713 Posted November 30, 2022 Author Share Posted November 30, 2022 Here is what I have done so far. Ordered the PS 3 from Ray. Bob. Quote Link to comment Share on other sites More sharing options...
Sean Posted December 1, 2022 Share Posted December 1, 2022 I'm looking forward toward a video with it running.. What are you using for running gear/ control ? Oh Ya very Hansom Quote Link to comment Share on other sites More sharing options...
rbrown7713 Posted December 1, 2022 Author Share Posted December 1, 2022 It will be PS3 and NWSL motor blocks. Bob Quote Link to comment Share on other sites More sharing options...
rbrown7713 Posted December 9, 2022 Author Share Posted December 9, 2022 Fitting the mth electronics in the B unit and hope that it clears the trucks, looks like it will. Bob. Quote Link to comment Share on other sites More sharing options...
Sean Posted December 11, 2022 Share Posted December 11, 2022 Looking good .. Quote Link to comment Share on other sites More sharing options...
enginear joe Posted December 15, 2022 Share Posted December 15, 2022 most people put in a decoder. You are putting in the whole DCS system! Wow. Love to watch the work progress. Thanks for sharing. Quote Link to comment Share on other sites More sharing options...
rbrown7713 Posted December 15, 2022 Author Share Posted December 15, 2022 The reason is, I like the sounds and control that the DCS system offers, plus that is all that I use, except for the smaller phone control. It doesn't have all of the controls that the full system has. What decoder that you have used that has the sound quality that the DCS system has? Bob. Quote Link to comment Share on other sites More sharing options...
rbrown7713 Posted December 15, 2022 Author Share Posted December 15, 2022 The reason that I used an F3 cab is that is has all of the proper mounts for the lights, cab interior light and the engineer and controls mount. In the B unit, I used a roof vent from the F3 also to allow the sound to escape from the B unit. Bob. Quote Link to comment Share on other sites More sharing options...
enginear joe Posted December 16, 2022 Share Posted December 16, 2022 Sorry Sir. I said decoder. I only use MTH board sets. I used to install other brands. I label them all "decoders". It appears that you are installing the whole DCS system in this case. What exactly is in that B unit? Quote Link to comment Share on other sites More sharing options...
rbrown7713 Posted December 16, 2022 Author Share Posted December 16, 2022 The TIU., and in the A unit will be the MTH decoder and battery. Bob. Quote Link to comment Share on other sites More sharing options...
rbrown7713 Posted December 19, 2022 Author Share Posted December 19, 2022 Here is where I installed the speed sensor. Bob. Quote Link to comment Share on other sites More sharing options...
rbrown7713 Posted December 19, 2022 Author Share Posted December 19, 2022 Some of you may know this about the center axle of the 3 axle NWSL block. The center axle does not have bushings between the case and the wheel as the outside axles have. The center one is allowed to float for tighter radii. Well sometimes the pickup bearing will float outside the case and cause the axle to tilt. It will not right itself, so the only way to correct this is to disassemble the block and re install this bearing. The white tabs that you see, were glued on the bearing to prevent the bearing from slipping outside of the case. The axles are still allowed to track back and forth without dislodging. Quote Link to comment Share on other sites More sharing options...
Sean Posted December 20, 2022 Share Posted December 20, 2022 You crafty devil Quote Link to comment Share on other sites More sharing options...
enginear joe Posted December 20, 2022 Share Posted December 20, 2022 7 hours ago, Sean said: You crafty devil Yep! Quote Link to comment Share on other sites More sharing options...
rbrown7713 Posted December 21, 2022 Author Share Posted December 21, 2022 All of the hard stuff is done, now just painting and final assembly is necessary. Won't be long. Bob. Quote Link to comment Share on other sites More sharing options...
Sean Posted December 21, 2022 Share Posted December 21, 2022 Quote Link to comment Share on other sites More sharing options...
rbrown7713 Posted December 22, 2022 Author Share Posted December 22, 2022 I have changed my mind about using the MTH cab. I removed the cab and replaced it with the Rich Garich cab as it looks more accurate than the MTH cab. I will have to construct the MTH mounts within the cab for mounting the MTH stuff. Bob. Quote Link to comment Share on other sites More sharing options...
rbrown7713 Posted December 27, 2022 Author Share Posted December 27, 2022 The mounts for the door, lights, cockpit have been mounted. Also the diaphrams have been fitted. This is plus for building in 1:32, even parts from other manufacturers fit. The door fits perfectly. Bob. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.